Balsa USA 1/3 scale cub help

[Mick Black]

Hi All
I have been given a crashed 1/3 scale cub. Unfortunately the chap who crashed it threw the smaller bits so piecing together to make a template isn’t possible.
I have tried to get a plan but with no luck. I am hoping someone on here has one who can do some measurements and maybe a pic of the front inside and out. I have the engine bulkhead but between the cab and the bulkhead is missing.
I do have a 1/4 scale cub but it doesn’t seem the same as the bigger cub

9472702B-AD2A-49D7-8902-5A01E5460F12.jpeg (360.89 KiB) Viewed 11489 times

[Alan Cantwell 1131]

http://shop.balsausa.com/product_p/a415.htm Also suggest contacting Steve Thomas, bobs models Orlando, Steve is the agent in the U.S for balsa USA, and would be able to source parts,

[Mick Black]

I Hi Alan and thanks for the reply I sent an email to that website but never received a reply I will try again.

Mick

[Bob Thompson1894]

You could try Stephen Thomas, not sure how much he could help, its obviously a bad time in the world. enquire@shopbobshobbycenter.com

[Bob Thompson1894]

http://www.shopbobshobbycenter.com/index.html

[Dave Kellett]

Hi Mick,
Try contacting Phil Clark at 'Fighteraces' he has a friend called 'Andy' and I know for certain he has this kit and drawings. I know because I sold it on to him.

Good luck and please let me know how you get on. If that fails then give Tony Parrot a call at Pegasus models Norwich. He is the UK importer for Balsa USA

Dave

[Mick Black]

Thanks again for the replies chaps. Pegasus models doesn’t have a delivery until July and has nothing on stock. I was hoping to repair it while I was stuck at home stuff from good old USA will take a while will try your other ideas.

Mick

[Alan Cantwell 1131]

I will ask steve to take a look

[Alan Cantwell 1131]

Dropped steve a message through Facebook, he has already acknowledged, think what you need, cowl, windscreens, former set etc,

[Alan Cantwell 1131]

Steve’s had a look at the post, he can get any parts you need, but suggests obtaining a plan here,

[Mick Black]

Hi Allan thanks for the help I can’t seem to find bobs models on internet but I’ll keep trying. I was hoping to rebuild it myself without buying cut wood. Just struggling with what it looks like between the dash panel and the engine bulkhead. I’m only trying to do it now because I’m bored and wanting something to play with. May have to just shelve it until this virus blows over.

Mick

[Mick Black]

Dave Keller
tried andy at fighter aces his friends daughter has the virus quite bad in hospital so was unable to help

[Bob Thompson1894]

just click on the link here---- http://www.shopbobshobbycenter.com/index.html

[Mick Black]

Ah thanks for that, I had found that but thought it was Bobs models

Thanks again

[paul hughes]

Hello Mick, I did reply to your pm last week but it appears you didn't get it. I'm sorry to say i can't find the plans. I must of lent them out but can't remember who to. sorry.

[paul hughes]

Just a thought, i know Steve Foxen had a cub, maybe he has the plans still

[Mick Black]

Okay Paul thanks for the reply
Mick

[John Rickett]

Hello MIck,
I have a Balsa USA J3 Cub plan.
I can't scan it as its too big, however I think I could scan the bulkhead former or at least trace round it and scan that, if you still need the information.
There is only the bulkhead former in front of the broken nose section shown in your picture and from the rear of that former to the front of the first vertical glazing bar is 362 mm

Regards
John

[John Rickett]

Mick,
I've managed to scan the former and can email it to you if you can provide details.

Regards
John

[Mick Black]

Cheers John email sent